Motor mount
Machined 7075 T6 aluminium  motor-mount with one-screw fixation and easy slider system.  Flex-free and very strong motormount. The space for the motor allows a maximum motor-length of 68mm, which covers most widely used motors.
  

Compact geardifferentials   
Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and o-rings.  Very light and durable outdrive cups in spring-steel.   Hardened spring-steel diff-coupler 13T with connector running in 2 oversized bearings 8x19x6 and ballbearing-13x19x4.   

Center solid axle for better acceleration / lower inertia.
   
Front and rear cvd-sets   
Both front and rear captured  driveshafts are being used with CVD system.  Durable yet light  spring steel engraved driveshafts with hard steel pins.   
   
Spring steel transmission parts   
The front and rear thin but strong spring steel cardan shafts connect the differentials with the gearbox section.    

Shockabsorbers big-bore 16mm   
Hard Teflon coated threaded shockbodies with 4mm shock-rods.  Black anodized aluminium screw on shock-tops with Serpent laser engraving.   Pre-load adjusters with o-rings inside.  Shocks use  large diameter membrames and large diameter o-rings  and bushings to create a  supersmooth  and leak-proof package.  Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.    
   
RCM shock springs   
Short type colorcoded shock springs are supplied for the 1st standard set-up  Springs are grinded flat top and bottom, and checked individually for tension and length.     

Wingmount and bodymounts rear   
Composite rear wing, with strong nylon adjustable rear bodymounts on wide body-support bridge located far enough to the rear, to support the bodies in best way.     
   
Captured pivot pins and balls and bolted hinge pins    
All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This insures your chances to finish an hour long main event, while battling for the lead.  This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.   
   

Rear suspension arms   
Durable oversized  lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.    
   
Rear  uprights  assembly   
Alumnium, black anodised and laser engraved uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong balljoints  to pre-set camber. Spring steel wheel-axles with large size bearings 8x16x5 and 13x19x4  with precision threaded aluminum wheel-hubs with +3 offset  . Rubber dustcovers in the rear to protect the cvd system and keep the lubrication inside. Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.   
   
Rear anti-roll bar   
The ballraced front anti-roll bar  system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors.  The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction  operation.   
   
Shocktower rear   / alu shock-risers
4.5mm thick carbon shocktower, integrated into the rear section for extra stiffness,  with 5 upper positioning holes for the shocks and 6 holes for roll-center positions.     The durable machined alu shock-risers in the rear allow for a more onroad aimed angle of the shockabsorber creating more overall grip and more predictable cornering.  

Shocktower and bodymounts front   / alu shock-risers
new 4.5mm thick carbon shocktower with 5 upper positioning holes for the shocks and and 6 holes for roll-center positions.  1 centrally located adjustable bodymount , and 2 forward mounted adjustable bodymounts, all with flip-tops.    The durable machined alu shock-risers in front allow for a more onroad aimed angle of the shockabsorber creating more overall grip and more predictable cornering.    
   
Angled steering system / servo saver   
The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension   
   
Ackermann plates   
With the design of the steering bell cranks when changing the Ackermann you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..    

Servo arms and linkages   
The servo arms have a splined insert to have the right fit per brand. The linkages runs very clean and tight and are easy to access to modify settings.   
   
Suspension brackets   
Beautifully machined  7075 T6  suspension brackets in anodized, laser angraved. Pecision fit for the nylon roll center inserts  and pivot balls / pins.  The GT 3.1 front suspension brackets make the pivot-pin and lower arm more horizontal, which improves handling and steering.  
   
Steeringblocks assembly    
Composite steeringblocks combined with 10 dgr C-hubs  for precise steering. Spring steel wheel-axles with large size bearings 8x18x5 and 15x21x4       with precision threaded aluminum wheel-hubs with +3 offset  . Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.   
   
Front suspension   
Durable oversized  lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.    
   
Front anti-roll bar   
The ballraced front anti-roll bar  system, consist of a spring steel bend wire, which is guided through the diff-cases and run in ballraced steel adaptors.  The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction  operation.   

Battery trays
The main eyecatchers are the extremely low laydown longtudinal placed battery-packs at each side of the car, being part of the side-guards, securely fastened with a flip-lid, for easy and fast battery changes. The weight low in the car and in the right position, well balanced. The Lipo holders comply with ROAR legal packs / dimensions.