BANTAM E-STATION BC6 (AC/DC 겸용, 셀발란서 내장형)

Specification
Operating voltage	DC 11~18 volts AC 100~240V, 50/60Hz
Charge/discharge power	max. 50/5 Watts
NiCd/MH	1~15 cells
LiIo/LiPo/LiFe	1~6 series
Pb	2~20V
Charge current	0.1 to 5.0A
Discharg current	0.1 to 1.0A
No. of cycle	1 to 5 times
Battery data memory	up to 5 data
Weight	1000g
Dimension	160x120x40 mm

Users setting-up parameters
Lithium battery voltage type	LiIo:3.6V, LiPo:3.7V, LiFe:3.3V
NiCd Delta-peak voltage sensitivity	5 to 20mV
NiMH Delta-peak voltage sensitivity	5 to 20mV
Battery temperature cut-off	20 to 80C or OFF
Waste time between charge/discharge	1 to 60 min.
Integral timer limit for safety	10 to 720 min.or OFF
Maximum charging capacity limit for safety	10 to 9990mAh or OFF
Key beep and buzzer sound	ON/OFF
Input DC power low alert	10 to 11V

- Optimized operating software

When charging or discharging, BC6 has an AUTO function that sets the feeding current or the cell count of Lithium battery automatically. Especially for Lithium batteries, it can prevent the over-charging can lead to an explosion by users fault. Every program in the unit is controlled with mutual links and communication for every possible error so it introduces a maximum safety. These can be set at users option.

- Dual input power

BC6 employs the circuit that can be operated with the input power of AC(Alternating Current) or DC(Direct Current). For AC input, it contains a AC-DC switching power supplier which has 5A of power capacity and maximum output power of 50Watts for charging. As a result it can charge up to 15 cells of NiCd/NiMH and 6 series of Lithium batteries with maximum current of 5.0A.

- Individual voltage balancer for Lithium batteries inside

BC6 has an individual-cell-voltage balancer inside. So it does not need any balancer separately when charging Lithium batteries (LiIo/LiPo/LiFe) for cell voltage balancing.

** When the Balance charge mode being performed, the balancing adapter should be connected to the balancing tab of battery pack, as well as the chargers charging lead should be connected to the output of battery pack.

And also, please pay attention to the polarity of the battery packs output which goes to the chargers output. If it is reversed, the short-circuit can be happened on the battery pack.

- Balance individual cells on discharge

BC6 also can monitor and balance individual cells of the Lithium battery pack during the discharge process. If the voltage of any one cell varies abnormally, the process will be stopped with the error message.

- Accept various types of Lithium battery

BC6 can accept three types of Lithium batteries - LiIo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job.

- Lithium battery Fast and Storage mode

You can charge Lithium battery for special purposes. Fast charge reduces the charging time of Lithium battery and Storage mode controls the final voltage of the battery to be suit for long time storage.

- Data store/load

For users convenience it can store maximum 5 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.

- Cyclic charging/discharging

Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.

- PC based analysis using USB communication

For technical expert, BC6 offers PC based program can analysis the characteristic of the battery by USB port. It shows a graph of voltage, current, capacity and temperature curves. It also shows the individual voltage of each cell in the Lithium battery pack.

- Robust outer aluminum case

High-quality aluminum case is durable and very efficient to cool out the internal heat